Facility Planning for 250-400 kVA UPSs for External Batteries
Input Specifications
| UPS rating | 250 kVA | 300 kVA | 400 kVA | ||||||
|---|---|---|---|---|---|---|---|---|---|
| Voltage (V) | 380 | 400 | 415 | 380 | 400 | 415 | 380 | 400 | 415 |
| Connections* | L1, L2, L3, N, PE | ||||||||
| Input voltage range (V) | 323-477 (full load) | ||||||||
| Frequency range (Hz) | 40-70 | ||||||||
| Nominal input current (A) | 404 | 384 | 370 | 485 | 461 | 444 | 647 | 614 | 592 |
| Maximum input current (A) |
474 |
451 |
434 |
568 |
540 |
520 |
757 |
719 |
693 |
| Input current limitation (A) | 600 | 720 | 960 | ||||||
| Total harmonic distortion (THDI) | <3% for linear loads <5% for non-linear loads |
||||||||
| Input power factor | >0.99 | ||||||||
| Maximum short circuit rating | Icc=35 kA | ||||||||
| Ramp-in | 7 seconds | ||||||||
Bypass Specifications
| UPS rating | 250 kVA | 300 kVA | 400 kVA | ||||||
|---|---|---|---|---|---|---|---|---|---|
| Voltage (V) | 380 | 400 | 415 | 380 | 400 | 415 | 380 | 400 | 415 |
| Connections | L1, L2, L3, N, PE | ||||||||
| Overload capacity | ≤115% continuous 125% for 10 minutes 150% for 1 minute |
||||||||
| Minimum bypass voltage (V) | 209 | 221 | 228 | 209 | 221 | 228 | 209 | 221 | 228 |
| Maximum bypass voltage (V) | 475 | 480 | 477 | 475 | 480 | 477 | 475 | 480 | 477 |
| Frequency (Hz) | 50 or 60 | ||||||||
| Frequency range (%) | ±1, ±2, ±4, ±5, ±10. Default is ±10 (user selectable). | ||||||||
| Nominal bypass current (A) |
384 |
364 |
351 |
460 |
437 |
422 |
614 |
583 |
562 |
| Maximum short circuit rating | Icc=35 kA | ||||||||
Output Specifications
| UPS rating | 250 kVA | 300 kVA | 400 kVA | ||||||
|---|---|---|---|---|---|---|---|---|---|
| Voltage (V) | 380 | 400 | 415 | 380 | 400 | 415 | 380 | 400 | 415 |
| Connections* | L1, L2, L3, N, PE | ||||||||
| Overload capacity* | 105% continuous 125% for 10 minutes 150% for 1 minute |
||||||||
| Output voltage regulation | ±1% | ||||||||
| Dynamic load response | 20 milliseconds | ||||||||
| Output power factor | 1 | ||||||||
| Nominal output current (A) |
380 |
361 |
348 |
456 |
433 |
417 |
608 |
577 |
556 |
| Total harmonic distortion (THDU) | <2% at 100% linear load <4% at 100% non-linear load |
||||||||
| Output frequency (Hz) | 50 or 60 | ||||||||
| Slew rate (Hz/sec) | Programmable: 0.5 to 2.0 Default is 0.5 |
||||||||
| Output performance classification (according to IEC/ EN62040-3) | VFI-SS-111 | ||||||||
| Load power factor | 0.5 leading to 0.5 lagging without derating | ||||||||
| Output short circuit current (inverter) | 630 A/200 ms | 820 A/200 ms | 1000 A/200 ms | ||||||
Battery Specifications
NOTE: The UPS supports 36-50 battery blocks.
| UPS rating | 250 kVA | 300 kVA | 400 kVA |
|---|---|---|---|
| Max. charging power in % of output power | 24 | ||
| Maximum charging power (kW) | 60 | 72 | 96 |
| Nominal battery voltage (VDC) | ±216 to ±300 | ||
| Nominal float voltage (VDC) | ±243 to ±337.5 | ||
| End of discharge voltage (full load) (VDC) | ±172.8 to ±240 | ||
| Battery current at full load and nominal battery voltage (A) |
615-443 |
738-531 |
985-709 |
| Battery current at full load and minimum battery voltage (A) |
769-554 |
923-664 |
1231-886 |
| Temperature compensation (per cell)* | Programmable from 0 to 7 mV/°C. Default is 0 mV/°C. | ||
| Ripple current | <5% C10 | ||
Recommended Upstream Protection
NOTE: For local directives which require 4-pole circuit breakers:
If neutral conductor is expected to carry a high current, due to line-neutral
non-linear load, the circuit breaker must be rated according to expected
neutral current.
| UPS rating | 250 kVA | 300 kVA | 400 kVA | |||
|---|---|---|---|---|---|---|
| Input | Bypass | Input | Bypass | Input | Bypass | |
| Breaker type | NSX630F Mic 2.3 (LV432877) | NSX630F Mic 2.3 (LV432877) | NS630bN Mic 2.0 (33463/NS33463) | NS630bN Mic 2.0 (33463/NS33463) | NS800N Mic 2.0 (33469/NS33469) | NS800N Mic 2.0 (33469/NS33469) |
| In setting | Io=500 | Io=500 | 1 | 1 | 1 | 1 |
| Ir setting | 0.95 | 0.9 | 0.9 | 0.9 | 0.95 | 0.9 |
| Im setting | Isd=1.5-10 | Isd=1.5-10 | Isd=1.5-10 | Isd=1.5-10 | Isd=1.5-10 | Isd=1.5-10 |
Recommended Cables Sizes
 DANGER |
|---|
|
hazard of electric shock, explosion, or arc flash
All wiring must comply with all applicable national and/or
electrical codes. The maximum allowable cable size is 240 mm².
Failure to follow these instructions will result in death or serious injury.
|
Cable sizes in this manual are based on table A.52-5 of IEC 60364-5-52 with the following assertions:
-
90 °C conductors
-
An ambient temperature of 30 °C
-
Use of copper conductors
-
Installation method C
PE size is based on table 54.3 of IEC 60364-5-54.
If the ambient temperature is greater than 30 °C, larger conductors are to be used in accordance with the correction factors of the IEC.
NOTE: Battery cables are sized according to 36 battery blocks. Contact
Schneider Electric for cable sizes for systems with more than 36 battery
blocks.
NOTE: The battery cable sizes given here are recommendations
– Always follow the specific instructions in the battery solution
documentation for battery cable sizes and battery PE cable sizes and
ensure that the battery cable sizes match the battery breaker rating.
NOTE: Recommended cable sizes and maximum allowable cable size may
vary for the auxiliary products. Refer to the installation manual
provided with the auxiliary product.
250 kVA – Copper
| Cable size per phase (mm2) | Neutral cable size (mm2) | PE cable size (mm2)) | |
|---|---|---|---|
| Input | 2 x 120 | 2 x 120 | 120 |
| Bypass | 2 x 120 | 2 x 120 | 120 |
| Output | 2 x 120 | 2 x 120 | 120 |
| Battery | 2 x 185 | 2 x 185 | 185 |
300 kVA – Copper
| Cable size per phase (mm2) | Neutral cable size (mm2) | PE cable size (mm2)) | |
|---|---|---|---|
| Input | 2 x 150 | 2 x 150 | 150 |
| Bypass | 2 x 150 | 2 x 150 | 150 |
| Output | 2 x 150 | 2 x 150 | 150 |
| Battery | 2 x 240 | 2 x 240 | 240 |
400 kVA – Copper
| Cable size per phase (mm2) | Neutral cable size (mm2) | PE cable size (mm2)) | |
|---|---|---|---|
| Input | 2 x 240 | 2 x 240 | 240 |
| Bypass | 2 x 240 | 2 x 240 | 240 |
| Output | 2 x 240 | 2 x 240 | 240 |
| Battery | 4 x 150 | 4 x 150 | 2 x 150 |
Recommended Bolts and Cable Lugs
| Cable Size (mm²) | Bolt Size | Cable Lug Type |
|---|---|---|
| 120 | M12x35 mm | TLK 120-12 |
| 150 | M12x35 mm | TLK 150-12 |
| 185 | M12x35 mm | TLK 185-12 |
| 240 | M12x35 mm | TLK 240-12 |
Torque Specifications
| Bolt Size | Torque |
|---|---|
| M12 | 50 Nm |
UPS Weights and Dimensions
| UPS rating | Weight kg | Height mm | Width mm | Depth mm |
|---|---|---|---|---|
| 250 kVA | 425 | 1970 | 600 | 850 |
| 300 kVA | 449 | 1970 | 600 | 850 |
| 400 kVA | 538 | 1970 | 600 | 850 |
UPS Shipping Weights and Dimensions
| UPS rating | Weight kg | Height mm | Width mm | Depth mm |
|---|---|---|---|---|
| 250 kVA | 470 | 2117 | 800 | 1000 |
| 300 kVA | 503 | 2117 | 800 | 1000 |
| 400 kVA | 584 | 2117 | 800 | 1000 |
Clearance
NOTE: Clearance dimensions are published for airflow and
service access only. Consult with the local safety codes and standards
for additional requirements in your local area.
NOTE: The minimum
rear clearance is 500 mm for maintenance and 350 mm for operation.
Environmental
| Operating | Storage | |
|---|---|---|
| Temperature | 0 °C to 30 °C | -15 °C to 40 °C for systems with batteries -25 °C to 55 °C for systems without batteries |
| Relative humidity | 0-95% non-condensing | |
| Elevation derating
according to IEC 62040-3 |
Power
derating factor: 0-1500 m: 1.000 1500-2000 m: 0.975 |
< 15000 m above sea level (or in an environment with equivalent air pressure) |
| Audible noise | <70 dBA at 100% load according to ISO3746 | |
| Protection class | IP20 (air filter as standard) | |
| Color | RAL 9003 | |
Heat Dissipation
| UPS rating | 250 kVA | 300 kVA | 400 kVA | |||
|---|---|---|---|---|---|---|
| W | BTU/hr | W | BTU/hr | W | BTU/hr | |
| Normal mode | 14500 | 49488 | 17400 | 59386 | 23200 | 79181 |
| Battery mode | 14000 | 47782 | 16800 | 57338 | 22400 | 76451 |
| ECO mode | 2000 | 6826 | 2400 | 8191 | 3200 | 10922 |