Upstream and Downstream Protection - Easy UPS 3S Pro 380/400/415 V

NOTE: For local directives which require 4-pole circuit breakers: If neutral conductor is expected to carry a high current, due to line-neutral non-linear load, the circuit breaker must be rated according to expected neutral current.

NOTE: For local directives which require 4-pole circuit breakers: Refer to the earthing diagrams for details about neutral connection.

The bypass/output disconnect devices are sized based on the nominal current +10%. This is to accommodate either low grid voltage or deviation in length between parallel UPSs. The battery disconnect devices are sized based on end-of-discharge voltage which has been defined as 308 VDC.

Required Upstream Protection for 380/400/415 V (IEC) and Minimum Prospective Phase-To-Earth Short Circuit at the UPS Input/Bypass Terminals

DANGER
Hazard of electric shock, explosion, or arc flash The upstream overcurrent protective device (and its settings) must be sized to ensure a disconnecting time within 0.07 seconds in case of a short circuit between the input/bypass phase and the UPS. Failure to follow these instructions will result in death or serious injury.

Compliance is assured with the recommended circuit breaker (and its settings) from the table below.

Required 3-Pole Upstream Protection for 3:3 UPS

NOTE: Ir must be set on the circuit breakers during start-up.

UPS rating	10 kVA
	Input			Bypass/Output			Battery
Voltage (V)	380	400	415	380	400	415	380-415
Circuit breaker type	NSX100B TM25D 3P3D, C10B3TM025			NSX100B TM25D 3P3D, C10B3TM025			ComPacT NSX100F DC 3P3D+TM40G, C10F3D+C103MG040*
In	25	25	25	25	25	25	40
Ir	0.8 x In	0.8 x In	0.8 x In	0.7 x In	0.7 x In	0.7 x In	0.9 x In
Im	300	300	300	300	300	300	100

UPS rating	15 kVA
	Input			Bypass/Output			Battery
Voltage (V)	380	400	415	380	400	415	380-415
Circuit breaker type	NSX100B NSX TM32D 3P3D, C10B3TM032			NSX100B TM32D 3P3D, C10B3TM032			ComPacT NSX100F DC 3P3D+TM63G, C10F3D+C103MG063*
In	32	32	32	32	32	32	63
Ir	In	In	In	0.9 x In	0.8 x In	0.8 x In	0.8 x In
Im	400	400	400	400	400	400	150

UPS rating	20 kVA
	Input			Bypass/Output			Battery
Voltage (V)	380	400	415	380	400	415	380-415
Circuit breaker type	NSX100B TM40D 3P3D, C10B3TM040			NSX100B TM40D 3P3D, C10B3TM040			ComPacT NSX100F DC 3P3D+TM80G, C10F3D+C103MG080*
In	40	40	40	40	40	40	80
Ir	In	In	In	0.9 x In	0.9 x In	0.8 x In	0.9 x In
Im	500	500	500	500	500	500	250

UPS rating	30 kVA
	Input			Bypass/Output			Battery
Voltage (V)	380	400	415	380	400	415	380-415
Circuit breaker type	NSX100B TM63D 3P3D, C10B3TM063			NSX100B TM63D 3P3D, C10B3TM063			ComPacT NSX160F DC 3P3D+TM125G, C16F3D+C163MG125D*
In	63	63	63	63	63	63	125
Ir	In	In	In	0.9 x In	0.8 x In	0.8 x In	0.8 x In
Im	500	500	500	500	500	500	530

UPS rating	40 kVA
	Input			Bypass/Output			Battery
Voltage (V)	380	400	415	380	400	415	380-415
Circuit breaker type	NSX100B TM63D 3P3D, C10B3TM080			NSX100B TM63D 3P3D, C10B3TM080			ComPacT NSX160F DC 3P3D+TM160G, C16F3D+C163MG160D*
In	80	80	80	80	80	80	160
Ir	In	In	In	0.9 x In	0.9 x In	0.8 x In	0.9 x In
Im	640	640	640	640	640	640	530

Required 4-Pole Upstream Protection for 3:3 UPS

NOTE: Ir must be set on the circuit breakers during start-up.

UPS rating	10 kVA
	Input			Bypass/Output			Battery
Voltage (V)	380	400	415	380	400	415	380-415
Circuit breaker type	NSX100B TM25D 4P3D, C10B6TM025			NSX100B TM25D 4P3D, C10B6TM025			ComPacT NSX100F DC 3P3D+TM40G, C10F3D+C103MG040*
In	25	25	25	25	25	25	40
Ir	0.8 x In	0.8 x In	0.8 x In	0.7 x In	0.7 x In	0.7 x In	0.9 x In
Im	300	300	300	300	300	300	100

UPS rating	15 kVA
	Input			Bypass/Output			Battery
Voltage (V)	380	400	415	380	400	415	380-415
Circuit breaker type	NSX100B TM40D 4P3D, C10B6TM040			NSX100B TM40D 4P3D, C10B6TM040			ComPacT NSX100F DC 3P3D+TM63G, C10F3D+C103MG063*
In	40	40	40	40	40	40	63
Ir	0.8 x In	0.8 x In	0.8 x In	0.7 x In	0.7 x In	0.7 x In	0.8 x In
Im	500	500	500	500	500	500	150

UPS rating	20 kVA
	Input			Bypass/Output			Battery
Voltage (V)	380	400	415	380	400	415	380-415
Circuit breaker type	NSX100B TM63D 4P3D, C10B6TM063			NSX100B TM63D 4P3D, C10B6TM063			ComPacT NSX100F DC 3P3D+TM80G, C10F3D+C103MG080*
In	63	63	63	63	63	63	80
Ir	0.7 x In	0.7 x In	0.7 x In	0.7 x In	0.7 x In	0.7 x In	0.9 x In
Im	500	500	500	500	500	500	250

UPS rating	30 kVA
	Input			Bypass/Output			Battery
Voltage (V)	380	400	415	380	400	415	380-415
Circuit breaker type	NSX100B TM80D 4P3D, C10B6TM080			NSX100B TM80D 4P3D, C10B6TM080			ComPacT NSX160F DC 3P3D+TM125G, C16F3D+C163MG125D*
In	80	80	80	80	80	80	125
Ir	0.8 x In	0.8 x In	0.8 x In	0.7 x In	0.7 x In	0.7 x In	0.8 x In
Im	640	640	640	640	640	640	530

UPS rating	40 kVA
	Input			Bypass/Output			Battery
Voltage (V)	380	400	415	380	400	415	380-415
Circuit breaker type	NSX100B TM100D 4P3D, C10B6TM100			NSX100B TM100D 4P3D, C10B6TM100			ComPacT NSX160F DC 3P3D+TM160G, C16F3D+C163MG160D*
In	100	100	100	100	100	100	160
Ir	0.8 x In	0.8 x In	0.8 x In	0.7 x In	0.7 x In	0.7 x In	0.9 x In
Im	800	800	800	800	800	800	530

Required 3-Pole Upstream Protection for 3:1 UPS – Single Mains

NOTE: Ir must be set on the circuit breakers during start-up.

UPS rating	10 kVA
	Input/Bypass			Output			Battery
Voltage (V)	380	400	415	220	230	240	380-415
Circuit breaker type	NSX100B TM63D 3P3D, C10B3TM063			NSX100B TM63D 2P2D, C10M2TM063			ComPacT NSX100F DC 3P3D+TM40G, C10F3D+C103MG040*
In	63	63	63	63	63	63	40
Ir	In	In	In	63 fixed	63 fixed	63 fixed	0.9 x In
Im	500	500	500	500	500	500	100

UPS rating	15 kVA
	Input/Bypass			Output			Battery
Voltage (V)	380	400	415	220	230	240	380-415
Circuit breaker type	NSX100B TM80D,3P3D, C10B3TM080			NSX100B TM80D 2P2D, C10M2TM080			ComPacT NSX100F DC 3P3D+TM63G, C10F3D+C103MG063*
In	80	80	80	80	80	80	63
Ir	In	In	In	80 fixed	80 fixed	80 fixed	0.8 x In
Im	640	640	640	640	640	640	150

UPS rating	20 kVA
	Input/Bypass			Output			Battery
Voltage (V)	380	400	415	220	230	240	380-415
Circuit breaker type	NSX100B TM100D,3P3D, C10B3TM100			NSX100B TM100D 2P2D, C10M2TM100			ComPacT NSX100F DC 3P3D+TM80G, C10F3D+C103MG080*
In	100	100	100	100	100	100	80
Ir	In	In	In	100 fixed	100 fixed	100 fixed	0.9 x In
Im	800	800	800	800	800	800	250

UPS rating	30 kVA
	Input/Bypass			Output			Battery
Voltage (V)	380	400	415	220	230	240	380-415
Circuit breaker type	NSX160B TM160D,3P3D, C16B3TM160			NSX160B TM160D 2P2D, C16M2TM160			ComPacT NSX160F DC 3P3D+TM125G, C16F3D+C163MG125D*
In	160	160	160	160	160	160	125
Ir	In	In	In	160 fixed	160 fixed	160 fixed	0.8 x In
Im	1250	1250	1250	1250	1250	1250	530

Required 3-Pole Upstream Protection for 3:1 UPS – Dual Mains

NOTE: Ir must be set on the circuit breakers during start-up.

UPS rating	10 kVA
	Input			Bypass/Output			Battery
Voltage (V)	380	400	415	220	230	240	380-415
Circuit breaker type	NSX100B TM25D 3P3D, C10B3TM025			NSX100B TM63D 2P2D, C10M2TM063			ComPacT NSX100F DC 3P3D+TM40G, C10F3D+C103MG040*
In	25	25	25	63	63	63	40
Ir	0.8 x In	0.8 x In	0.8 x In	63 fixed	63 fixed	63 fixed	0.9 x In
Im	300	300	300	500	500	500	100

UPS rating	15 kVA
	Input			Bypass/Output			Battery
Voltage (V)	380	400	415	220	230	240	380-415
Circuit breaker type	NSX100B NSX TM32D 3P3D, C10B3TM032			NSX100B TM80D 2P2D, C10M2TM080			ComPacT NSX100F DC 3P3D+TM63G, C10F3D+C103MG063*
In	32	32	32	80	80	80	63
Ir	In	In	In	80 fixed	80 fixed	80 fixed	0.8 x In
Im	400	400	400	640	640	640	150

UPS rating	20 kVA
	Input			Bypass/Output			Battery
Voltage (V)	380	400	415	220	230	240	380-415
Circuit breaker type	NSX100B TM40D 3P3D, C10B3TM040			NSX100B TM100D 2P2D, C10M2TM100			ComPacT NSX100F DC 3P3D+TM80G, C10F3D+C103MG080*
In	40	40	40	100	100	100	80
Ir	In	In	In	100 fixed	100 fixed	100 fixed	0.9 x In
Im	500	500	500	800	800	800	250

UPS rating	30 kVA
	Input			Bypass/Output			Battery
Voltage (V)	380	400	415	220	230	240	380-415
Circuit breaker type	NSX100B TM63D 3P3D, C10B3TM063			NSX160B TM160D 2P2D, C16M2TM160			ComPacT NSX160F DC 3P3D+TM125G, C16F3D+C163MG125D*
In	63	63	63	160	160	160	125
Ir	In	In	In	160 fixed	160 fixed	160 fixed	0.8 x In
Im	500	500	500	1250	1250	1250	530

Required 4-Pole Upstream Protection for 3:1 UPS – Single Mains

NOTE: Ir must be set on the circuit breakers during start-up.

UPS rating	10 kVA
	Input/Bypass			Output			Battery
Voltage (V)	380	400	415	220	230	240	380-415
Circuit breaker type	NSX100B TM63D 4P3D, C10B6TM063			NSX100B TM63D 2P2D, C10M2TM063			ComPacT NSX100F DC 3P3D+TM40G, C10F3D+C103MG040*
In	63	63	63	63	63	63	40
Ir	In	In	In	63 fixed	63 fixed	63 fixed	0.9 x In
Im	500	500	500	500	500	500	100

UPS rating	15 kVA
	Input/Bypass			Output			Battery
Voltage (V)	380	400	415	220	230	240	380-415
Circuit breaker type	NSX100B TM80D,4P3D, C10B6TM080			NSX100B TM80D 2P2D, C10M2TM080			ComPacT NSX100F DC 3P3D+TM63G, C10F3D+C103MG063*
In	80	80	80	80	80	80	63
Ir	In	In	In	80 fixed	80 fixed	80 fixed	0.8 x In
Im	640	640	640	640	640	640	150

UPS rating	20 kVA
	Input/Bypass			Output			Battery
Voltage (V)	380	400	415	220	230	240	380-415
Circuit breaker type	NSX100B TM100D,4P3D, C10B6TM100			NSX100B TM100D 2P2D, C10M2TM100			ComPacT NSX100F DC 3P3D+TM80G, C10F3D+C103MG080*
In	100	100	100	100	100	100	80
Ir	In	In	In	100 fixed	100 fixed	100 fixed	0.9 x In
Im	800	800	800	800	800	800	250

UPS rating	30 kVA
	Input/Bypass			Output			Battery
Voltage (V)	380	400	415	220	230	240	380-415
Circuit breaker type	NSX160B TM160D,4P3D, C16B3TM160			NSX160B TM160D 2P2D, C16M2TM160			ComPacT NSX160F DC 3P3D+TM125G, C16F3D+C163MG125D*
In	160	160	160	160	160	160	125
Ir	In	In	In	160 fixed	160 fixed	160 fixed	0.8 x In
Im	1250	1250	1250	1250	1250	1250	530

Required 4-Pole Upstream Protection for 3:1 UPS – Dual Mains

NOTE: Ir must be set on the circuit breakers during start-up.

UPS rating	10 kVA
	Input			Bypass/Output			Battery
Voltage (V)	380	400	415	220	230	240	380-415
Circuit breaker type	NSX100B TM25D 4P3D, C10B6TM025			NSX100B TM63D 2P2D, C10M2TM063			ComPacT NSX100F DC 3P3D+TM40G, C10F3D+C103MG040*
In	25	25	25	63	63	63	40
Ir	0.8 x In	0.8 x In	0.8 x In	63 fixed	63 fixed	63 fixed	0.9 x In
Im	300	300	300	500	500	500	100

UPS rating	15 kVA
	Input			Bypass/Output			Battery
Voltage (V)	380	400	415	220	230	240	380-415
Circuit breaker type	NSX100B NSX TM40D 4P3D, C10B6TM040			NSX100B TM80D 2P2D, C10M2TM080			ComPacT NSX100F DC 3P3D+TM63G, C10F3D+C103MG063*
In	40	40	40	80	80	80	63
Ir	0.8 x In	0.8 x In	0.8 x In	80 fixed	80 fixed	80 fixed	0.8 x In
Im	500	500	500	640	640	640	150

UPS rating	20 kVA
	Input			Bypass/Output			Battery
Voltage (V)	380	400	415	220	230	240	380-415
Circuit breaker type	NSX100B TM63D 4P3D, C10B6TM063			NSX100B TM100D 2P2D, C10M2TM100			ComPacT NSX100F DC 3P3D+TM80G, C10F3D+C103MG080*
In	63	63	63	100	100	100	80
Ir	0.7 x In	0.7 x In	0.7 x In	100 fixed	100 fixed	100 fixed	0.9 x In
Im	500	500	500	800	800	800	250

UPS rating	30 kVA
	Input			Bypass/Output			Battery
Voltage (V)	380	400	415	220	230	240	380-415
Circuit breaker type	NSX100B TM80D 4P3D, C10B6TM080			NSX160B TM160D 2P2D, C16M2TM160			ComPacT NSX160F DC 3P3D+TM125G, C16F3D+C163MG125D*
In	80	80	80	160	160	160	125
Ir	0.8 x In	0.8 x In	0.8 x In	160 fixed	160 fixed	160 fixed	0.8 x In
Im	640	640	640	1250	1250	1250	530

Recommended Downstream Protection for 380/400/415 V (IEC) for 3:3 UPS

UPS rating	Circuit breaker type
10 kVA	IC65H-4P-B 4A
15 kVA	IC65H-4P-B 6A
20 kVA	IC65H-4P-C 6A
30 kVA	IC65H-4P-C 6A
40 kVA	IC65H-4P-B 10A

Recommended Downstream Protection for 380/400/415 V (IEC) for 3:1 UPS

UPS rating	Circuit breaker type
10 kVA	IC65H-2P-B 10A
15 kVA	IC65H-2P-B 16A
20 kVA	IC65H-2P-B 20A
30 kVA	IC65H-2P-B 32A