Product Related Information

Read and understand these instructions before performing any procedure with this device.

DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH Only appropriately trained persons who are familiar with and understand the contents of this manual and all other pertinent product documentation and who have received safety training to recognize and avoid hazards involved are authorized to work on and with this system. Installation, adjustment, repair and maintenance must be performed by qualified personnel. The system integrator is responsible for compliance with all local and national electrical code requirements as well as all other applicable regulations with respect to grounding of all equipment. Many components of the product, including the printed circuit boards, operate with mains voltage. Do not touch. Use only electrically insulated tools. Do not touch unshielded components or terminals with voltage present. Motors can generate voltage when the shaft is rotated. Prior to performing any type of work on the system, block the motor shaft to prevent rotation. AC voltage can couple voltage to unused conductors in the motor cable. Insulate both ends of unused conductors of the motor cable. Before performing work on the system, disconnect all power including external control power that may be present; place a Do Not Turn On label on all power switches; and lock all power switches in the open position. Install and close all covers before applying voltage. Failure to follow these instructions will result in death or serious injury.

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH

Only appropriately trained persons who are familiar with and understand the contents of this manual and all other pertinent product documentation and who have received safety training to recognize and avoid hazards involved are authorized to work on and with this system. Installation, adjustment, repair and maintenance must be performed by qualified personnel.

The system integrator is responsible for compliance with all local and national electrical code requirements as well as all other applicable regulations with respect to grounding of all equipment.

Many components of the product, including the printed circuit boards, operate with mains voltage. Do not touch. Use only electrically insulated tools.

Do not touch unshielded components or terminals with voltage present.

Motors can generate voltage when the shaft is rotated. Prior to performing any type of work on the system, block the motor shaft to prevent rotation.

AC voltage can couple voltage to unused conductors in the motor cable. Insulate both ends of unused conductors of the motor cable.

Before performing work on the system, disconnect all power including external control power that may be present; place a Do Not Turn On label on all power switches; and lock all power switches in the open position.

Install and close all covers before applying voltage.

Failure to follow these instructions will result in death or serious injury.

Controllers may perform unexpected movements because of incorrect wiring, incorrect settings, incorrect data, or other user errors.

Damaged products or accessories may cause electric shock or unanticipated equipment operation.

DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH Do not use damaged products or accessories. Failure to follow these instructions will result in death or serious injury.

Contact your local Schneider Electric sales office if you detect any damage whatsoever.

WARNING
UNANTICIPATED EQUIPMENT OPERATION Carefully install the wiring in accordance with the EMC requirements. Do not operate the product with unknown or unsuitable settings or data. Perform a comprehensive commissioning test. Failure to follow these instructions can result in death, serious injury, or equipment damage.

WARNING
LOSS OF CONTROL The designer of any control scheme must consider the potential failure modes of control paths and, for critical functions, provide a means to achieve an acceptable state during and after a path interruption. Separate or redundant control paths must be provided for critical control functions. System control paths may include communication links. Consideration must be given to the implications of anticipated transmission delays or interruptions of the link. Observe all accident prevention regulations and local safety guidelines.* Each implementation of an LTMR controller must be individually and thoroughly tested for proper operation before being placed into service. Failure to follow these instructions can result in death, serious injury, or equipment damage.

WARNING

LOSS OF CONTROL

The designer of any control scheme must consider the potential failure modes of control paths and, for critical functions, provide a means to achieve an acceptable state during and after a path interruption.
Separate or redundant control paths must be provided for critical control functions.
System control paths may include communication links. Consideration must be given to the implications of anticipated transmission delays or interruptions of the link.
Observe all accident prevention regulations and local safety guidelines.*
Each implementation of an LTMR controller must be individually and thoroughly tested for proper operation before being placed into service.

Failure to follow these instructions can result in death, serious injury, or equipment damage.

WARNING: This product can expose you to chemicals including lead and lead compounds, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov .