TeSys Active TeSys island – Digital Motor Management Solution – System, Installation, and Operation Guide

Safety Information
About the Book
Precautions
TeSys island Presentation
TeSys Avatar Functions
Installation and Wiring
- Installation
  - Dimensions
  - Weights
  - General Installation Guidelines
    - Enclosure Requirements
    - Thermal Considerations
    - Environmental Characteristics
    - Electromagnetic Compatibility
  - Mounting Positions
  - Required Tools
  - Installing the Bus Coupler
    - Mounting the Bus Coupler on DIN Rail
    - Micro SD Card
      - Handling the Micro SD Card
      - Installing the Micro SD Card
  - Installing Standard Starters and SIL Starters
    - Coupling Starters
    - Installing the LAD9R1 Kit (9–38 A Starters)
    - Installing the LAD9P3 Shorting Block (9–38 A Starters in Y/D Avatars)
    - Installing the LAD9R3 Kit (40–65 A Starters)
    - Installing the LAD9SD3S Shorting Block (40–65 A Starters in Y/D Avatars)
    - Mounting Starters on DIN Rail
  - Mounting Power Interface Modules on DIN Rail
  - Mounting the I/O and Interface Modules on DIN Rail
  - Installation Verification
  - Connecting the Flat Cables
- Wiring
- Installation Setup
Operations
- OMT Operations
Powering On the island
Powering Off the island
Module LEDs
Updating the Firmware on the Bus Coupler
Device Replacement
- Bus Coupler Replacement
  - Micro SD Card
  - FDR Server
  - SoMove™ Project File
- Module Replacement
Alarms and Events
System Logs
- Event Log
  - Event Log Priority
  - System Event Log Attributes
- Audit Log
  - Audit Log Format
  - System Command Events
  - User Login Events
  - Island Topology Change Events
  - File Transfer Events
Troubleshooting
- Avatar Device Event
- Performing a Factory Reset
Appendix
- Avatar Composition
- Avatar Wiring Schematics and Accessory Diagrams
  - Bus Coupler with I/O Modules and Voltage Interface Modules
  - Switch
  - Switch - SIL Stop, W. Cat 1/2
  - Switch - SIL Stop, W. Cat 3/4
  - Digital I/O
  - Analog I/O
  - Power Interface without I/O (Measure)
  - Power Interface with I/O (Control)
  - Motor One Direction
  - Motor One Direction - SIL Stop, W. Cat 1/2
  - Motor One Direction - SIL Stop, W. Cat 3/4
  - Motor Two Directions
  - Motor Two Directions - SIL Stop, W. Cat 1/2
  - Motor Two Directions - SIL Stop, W. Cat 3/4
  - Motor Y/D One Direction
  - Motor Y/D Two Directions
  - Motor Two Speeds
  - Motor Two Speeds with Dahlandar Option
  - Motor Two Speeds - SIL Stop, W. Cat 1/2
  - Motor Two Speeds - SIL Stop, W. Cat 3/4
  - Motor Two Speeds Two Directions
  - Motor Two Speeds Two Directions - SIL Stop, W. Cat 1/2
  - Motor Two Speeds Two Directions - SIL Stop, W. Cat 3/4
  - Resistor
  - Power Supply
  - Transformer
  - Pump
  - Conveyor One Direction
  - Conveyor One Direction - SIL Stop, W. Cat 1/2
  - Conveyor Two Directions
  - Conveyor Two Directions - SIL Stop, W. Cat 1/2

DOCA0270EN-02

System Avatar Settings

Configure the system Avatar settings for the Fieldbus and Ethernet services settings.

System Avatar Settings

Step	Action
1	Click on the SETTINGS tab in the DTM tool.
2	Under AVATARS, click the System Avatar.
3	Configure the system Avatar settings for the Fieldbus and Ethernet services settings.
4	Click OK to confirm the settings. Save the project.

Show QR code for this page

QR Code is a registered trademark of DENSO WAVE INCORPORATED in Japan and other countries.

Was this helpful?

Contact Information

Legal Information

Change your cookie settings