TeSys Active TeSys island – Digital Motor Management Solution – System, Installation, and Operation Guide

Safety Information
About the Book
Precautions
TeSys island Presentation
TeSys Avatar Functions
Installation and Wiring
- Installation
  - Dimensions
  - Weights
  - General Installation Guidelines
    - Enclosure Requirements
    - Thermal Considerations
    - Environmental Characteristics
    - Electromagnetic Compatibility
  - Mounting Positions
  - Required Tools
  - Installing the Bus Coupler
    - Mounting the Bus Coupler on DIN Rail
    - Micro SD Card
      - Handling the Micro SD Card
      - Installing the Micro SD Card
  - Installing Standard Starters and SIL Starters
    - Coupling Starters
    - Installing the LAD9R1 Kit (9–38 A Starters)
    - Installing the LAD9P3 Shorting Block (9–38 A Starters in Y/D Avatars)
    - Installing the LAD9R3 Kit (40–65 A Starters)
    - Installing the LAD9SD3S Shorting Block (40–65 A Starters in Y/D Avatars)
    - Mounting Starters on DIN Rail
  - Mounting Power Interface Modules on DIN Rail
  - Mounting the I/O and Interface Modules on DIN Rail
  - Installation Verification
  - Connecting the Flat Cables
- Wiring
- Installation Setup
Operations
- OMT Operations
Powering On the island
Powering Off the island
Module LEDs
Updating the Firmware on the Bus Coupler
Device Replacement
- Bus Coupler Replacement
  - Micro SD Card
  - FDR Server
  - SoMove™ Project File
- Module Replacement
Alarms and Events
System Logs
- Event Log
  - Event Log Priority
  - System Event Log Attributes
- Audit Log
  - Audit Log Format
  - System Command Events
  - User Login Events
  - Island Topology Change Events
  - File Transfer Events
Troubleshooting
- Avatar Device Event
- Performing a Factory Reset
Appendix
- Avatar Composition
- Avatar Wiring Schematics and Accessory Diagrams
  - Bus Coupler with I/O Modules and Voltage Interface Modules
  - Switch
  - Switch - SIL Stop, W. Cat 1/2
  - Switch - SIL Stop, W. Cat 3/4
  - Digital I/O
  - Analog I/O
  - Power Interface without I/O (Measure)
  - Power Interface with I/O (Control)
  - Motor One Direction
  - Motor One Direction - SIL Stop, W. Cat 1/2
  - Motor One Direction - SIL Stop, W. Cat 3/4
  - Motor Two Directions
  - Motor Two Directions - SIL Stop, W. Cat 1/2
  - Motor Two Directions - SIL Stop, W. Cat 3/4
  - Motor Y/D One Direction
  - Motor Y/D Two Directions
  - Motor Two Speeds
  - Motor Two Speeds with Dahlandar Option
  - Motor Two Speeds - SIL Stop, W. Cat 1/2
  - Motor Two Speeds - SIL Stop, W. Cat 3/4
  - Motor Two Speeds Two Directions
  - Motor Two Speeds Two Directions - SIL Stop, W. Cat 1/2
  - Motor Two Speeds Two Directions - SIL Stop, W. Cat 3/4
  - Resistor
  - Power Supply
  - Transformer
  - Pump
  - Conveyor One Direction
  - Conveyor One Direction - SIL Stop, W. Cat 1/2
  - Conveyor Two Directions
  - Conveyor Two Directions - SIL Stop, W. Cat 1/2

DOCA0270EN-02

Certificate Manager

Certificate Manager allows you to configure security certificate to the TeSys island.

The user-supplied certificates can be only deleted. Once the certificate is deleted, the TeSys island assigns the self-signed certificate by default.

Self-signed certificate cannot be deleted and it can only be overridden by the user-supplied certificate.

To upload the certificate, do the following:

In the Admin Options panel, click the arrow to expand the Certificate Manager.
In the Upload Certificate window, click Choose File to select the .p12 certificate.
Enter the certificate password and click Submit.

NOTE:

For certificate without password, leave the password field empty.
To support secure communications with HTTPS, the certificate must be imported in the browser of the PC.

Certificate Manager

Show QR code for this page

QR Code is a registered trademark of DENSO WAVE INCORPORATED in Japan and other countries.

Was this helpful?

Contact Information

Legal Information

Change your cookie settings