Event List

@experts: the list is based on v7–23 of the Event Census

Event Characteristics

The events are listed according to the history in which they are logged.

Each event is defined by the following characteristics:

Code: event code
Event: user message
History
Type: not customizable
- Entry/Exit: occurrence/completion event.
- Pulse: instantaneous event.
Latched:
- Yes: the event is latched and the user must reset the event status.
- No: the event is unlatched.
Activity:
- Enabled
- Disabled
Severity:
- High severity events.
- Medium severity events.
- Low severity events.

Trip Events

Code	Event	History	Type	Latched	Activity	Severity
0x4000 (16384)	Long Time (Ir) trip	Trip	Pulse	Yes	Enabled	High
0x4001 (16385)	Short Time (Isd) trip	Trip	Pulse	Yes	Enabled	High
0x4002 (16386)	Instantaneous (Ii) trip	Trip	Pulse	Yes	Enabled	High
0x4003 (16387)	Ground Fault (Ig) trip	Trip	Pulse	Yes	Enabled	High
0x4005 (16389)	Control unit over temperature trip	Trip	Pulse	Yes	Enabled	High
0x4006 (16390)	Ultimate self-protection (SELLIM) trip	Trip	Pulse	Yes	Enabled	High
0x4007 (16391)	Self diagnostic trip. Replace control unit	Trip	Pulse	Yes	Enabled	High
0x400A (16394)	ENCT Disconnected trip	Trip	Pulse	Yes	Enabled	High
0x401D (16413)	Ultimate self-protection (DIN/DINF) trip	Trip	Pulse	Yes	Enabled	High
0x401E (16414)	Ig test trip	Trip	Pulse	Yes	Enabled	High
0x4033 (16435)	Current sensor loss. Replace Circuit Breaker	Trip	Pulse	Yes	Enabled	High
0x4035 (16437)	Ii test trip	Trip	Pulse	Yes	Enabled	High

Protection Events

Code	Event	History	Type	Latch	Activity	Severity
0x0F11 (3857)	Thermal memory reset order	Protection	Pulse	No	Enabled	Low
0x03F5 (1013)	Ir pre-alarm (I > 90% Ir)	Protection	Entry/Exit	No	Enabled	Medium
0x6200 (25088)	Ir start (I > 105% Ir)	Protection	Entry/Exit	No	Enabled	High
0x6201 (25089)	Isd start	Protection	Entry/Exit	No	Enabled	Low
0x6203 25091	Ig start	Protection	Entry/Exit	No	Enabled	Low
0x0C03 (3075)	ERMS engaged	Protection	Entry/Exit	No	Enabled	Low
0x0C08 (3080)	Ii protection disabled	Protection	Pulse	No	Enabled	Low
0x0C09 (3081)	Ig protection disabled	Protection	Pulse	No	Enabled	Low
0x1100 (4352)	Protection changed by HMI	Protection	Pulse	No	Enabled	Low
0x1108 (4360)	Protection changed by communication	Protection	Pulse	No	Enabled	Low

Diagnostic Events

Code	Event	History	Type	Latch	Activity	Severity
0x1122 (4386)	Communication lost with EIFE or IFE module	Diagnostic	Entry/Exit	No	Enabled	Medium
0x1123 (4387)	Communication lost with IFM module	Diagnostic	Entry/Exit	No	Enabled	Medium
0x1302 (4866)	Control Unit in test mode	Diagnostic	Entry/Exit	No	Enabled	Low
0x1303 (4867)	Injection test in progress	Diagnostic	Entry/Exit	No	Enabled	Low
0x1304 (4868)	Test aborted by user	Diagnostic	Pulse	No	Enabled	Low
0x1400 (5120)	Self test 1. Replace control unit	Diagnostic	Entry/Exit	No	Enabled	High
0x1404 (5124)	Control unit over temperature	Diagnostic	Entry/Exit	No	Enabled	High
0x1405 (5125)	Self test 3. Replace control unit	Diagnostic	Entry/Exit	No	Enabled	High
0x1406 (5126)	Self test 4. Replace control unit	Diagnostic	Entry/Exit	No	Enabled	High
0x1416 (5142)	Mitop disconnected. Call Schneider Electric support	Diagnostic	Entry/Exit	No	Enabled	High
0x1460 (5216)	Invalid self test - MX1 voltage release	Diagnostic	Entry/Exit	No	Disabled	Medium
0x1461 (5217)	MX voltage release not detected	Diagnostic	Entry/Exit	No	Disabled	Medium
0x1462 (5218)	Invalid self test - XF voltage release	Diagnostic	Entry/Exit	No	Disabled	Medium
0x1463 (5219)	XF voltage release not detected	Diagnostic	Entry/Exit	No	Disabled	Medium
0x1518 (5400)	Self-test 6. Replace control unit	Diagnostic	Entry/Exit	No	Enabled	High
0x1402 (5122)	Current sensor loss. Replace circuit breaker	Diagnostic	Entry/Exit	No	Enabled	High
0x1403 (5123)	ENCT disconnected	Diagnostic	Entry/Exit	No	Enabled	High
0x1430 (5168)	Protection settings reset to factory values	Diagnostic	Entry/Exit	No	Enabled	High
0x142F (5167)	Last protection settings have not been applied	Diagnostic	Entry/Exit	No	Enabled	Medium
0x140F (5135)	Protection settings not accessible 1	Diagnostic	Entry/Exit	No	Enabled	Medium
0x1474 (5236)	Protection settings not accessible 2	Diagnostic	Entry/Exit	No	Enabled	Medium
0x1473 (5235)	Internal access loss. Reboot control unit	Diagnostic	Entry/Exit	No	Enabled	Medium
0x1433 (5171)	Replace internal battery	Diagnostic	Entry/Exit	No	Enabled	Low
0x1437 (5175)	Internal battery not detected	Diagnostic	Entry/Exit	No	Enabled	Low
0x1436 (5174)	Control unit memory degradation	Diagnostic	Pulse	No	Enabled	Low
0x1409 (5129)	Unable to read sensor plug	Diagnostic	Entry/Exit	No	Enabled	High
0x0D00 (3328)	Critical hardware modules discrepancy	Diagnostic	Entry/Exit	No	Enabled	Medium
0x0D01 (3329)	Critical firmware modules discrepancy	Diagnostic	Entry/Exit	No	Enabled	Medium
0x0D02 (3330)	Non-critical hardware modules discrepancy	Diagnostic	Entry/Exit	No	Enabled	Medium
0x0D03 (3331)	Non-critical firmware modules discrepancy	Diagnostic	Entry/Exit	No	Enabled	Medium
0x0D09 (3337)	Firmware discrepancy within control unit	Diagnostic	Entry/Exit	No	Enabled	Medium
0x0D0A (3338)	Invalid CU factory config. 1	Diagnostic	Entry/Exit	No	Enabled	Low
0x1413 (5139)	Ig test - no trip	Diagnostic	Pulse	No	Enabled	High
0x142A (5162)	Ig test launched	Diagnostic	Pulse	No	Enabled	Low
0x151B (5403)	Ii test - no trip	Diagnostic	Pulse	No	Enabled	High
0x151C (5404)	Ii test button pressed	Diagnostic	Pulse	No	Enabled	Low
0x1482 (5250)	Sched. Manufact. maintenance within 3 months	Diagnostic	Entry/Exit	No	Enabled	Medium
0x1440 (5184)	Contact wear > 60%. Check contacts	Diagnostic	Entry/Exit	No	Enabled	Medium
0x1441 (5185)	Contact wear > 95%. Plan circuit breaker replacement	Diagnostic	Entry/Exit	No	Enabled	Medium
0x1442 (5186)	Contact wear > 100%. Replace circuit breaker	Diagnostic	Entry/Exit	No	Enabled	High
0x150F (5391)	Iron CT loss. Replace circuit breaker	Diagnostic	Entry/Exit	No	Enabled	High
0x1517 (5399)	Current unbalance > 50%. Check load balancing	Diagnostic	Entry/Exit	No	Enabled	Low
0x1421 (5153)	Invalid PowerTag communication	Diagnostic	Entry/Exit	No	Enabled	Medium
0x1423 (5155)	Loss of Zigbee communication with Gateway	Diagnostic	Entry/Exit	No	Enabled	Low
0x1800 (6144)	Communication lost with BCIM	Diagnostic	Entry/Exit	No	Enabled	Medium
0x1802 (6146)	BCIM in Critical Status	Diagnostic	Entry/Exit	No	Enabled	Medium
0x1803 (6147)	BCIM in non-Critical Status	Diagnostic	Entry/Exit	No	Enabled	Medium

Operation Events

Code	Event	History	Type	Latch	Activity	Severity
0x0410 (1040)	Opening order sent to MX voltage release	Operation	Pulse	No	Enabled	Low
0x0411 (1041)	Closing order sent to XF voltage release	Operation	Pulse	No	Enabled	Low
0x1000 (4096)	Circuit breaker opened	Operation	Pulse	No	Enabled	Low
0x1001 (4097)	Circuit breaker closed	Operation	Pulse	No	Enabled	Low
0x1002 (4098)	Manual mode enabled	Operation	Pulse	No	Enabled	Low
0x1004 (4100)	Local mode enabled	Operation	Pulse	No	Enabled	Low
0x1307 (4871)	Alarm reset	Operation	Pulse	No	Enabled	Low
0x112B (4395)	Control unit firmware update mode	Operation	Entry/Exit	No	Enabled	Low
0x112C (4396)	Control unit firmware update unsuccessful	Operation	Pulse	No	Enabled	Low
0x1107 (4359)	Date and time set	Operation	Pulse	No	Enabled	Low
0x1301 (4865)	Connection on USB port	Operation	Entry/Exit	No	Enabled	Low
0x1801 (6145)	BCIM update unsuccessful	Operation	Pulse	No	Enabled	Low