Configuration of PowerTag Control Devices Through Webpages

To configure PowerTag Control devices with EcoStruxure Panel Server webpages, proceed as follows:

Navigate to Settings > Wireless Devices > Wireless Devices to view the list of the paired wireless devices.

Result: The list of paired devices is displayed (with Connected written in green under the device name).
Select the required PowerTag Control device to modify the configuration.

Result: The parameters of the PowerTag Control device are displayed.
If necessary, in Locate, click Start to identify the specific device in its location. The PowerTag Control device LED blinks for 30 seconds.
Enter the data in the fields, referring to the following tables for more information about the parameters.
Click Apply Changes to save the settings
- or
- Click Cancel Changes to revert the settings.

NOTE: When saving the settings, a message may be displayed indicating either that 90% of wireless bandwidth capacity is reached or that the Panel Server is over configured. Follow the recommendation in the message to increase the communication period of a particular device or to reduce the number of wireless devices.

Parameter Tables

Identification

Parameter name	Description
Name	Enter the name of the wireless device.
Label (optional)	Enter the label of the wireless device.
RF-id	For display only
Device range	For display only
Commercial reference	For display only
Hardware revision	For display only
Device family	For display only

Communication Settings

Parameter name	Description
Communication period (s)	When available for the selected wireless device, you can set the communication period at a value different from the value set at family devices level. Select a value of between 5 and 120 seconds from the list.

Modbus virtual

Parameter name	Description
Virtual server ID	Enter the ID of the Modbus virtual server.

Input/Output Settings

Parameter name	Description
Local Control	Toggles local control on or off.
Configuration Type	Select from the list: Contactor without feedback loop: Configure parameters for Output and Input separately Contactor with feedback loop Impulse relay The parameters displayed depend on the selection of configuration type. See details in the following tables.

Parameter name

Description

Local Control

Toggles local control on or off.

Configuration Type

Select from the list:

Contactor without feedback loop: Configure parameters for Output and Input separately
Contactor with feedback loop
Impulse relay

The parameters displayed depend on the selection of configuration type. See details in the following tables.

Parameters for Contactor without feedback loop

Parameter name		Description
Output	I/O Type	Select from the list: Standard I/O Not connected
	Name	Enter the name of the wireless device.
	Label	Enter the label of the wireless device (optional).
	I/O Contextualization	Select an option from the list.
	Status name	If you select Custom as contextualization option, then enter the custom name for the device.
	Meaning of output = 0	Displayed values depend on selection of I/O Contextualization. Enter your custom values if you select Custom as contextualization option. NOTE: Clicking the double arrow icon on the right allows you to swap the meanings of outputs 0 and 1.
	Meaning of output = 1	Displayed values depend on selection of I/O Contextualization. Enter your custom values if you select Custom as contextualization option. NOTE: Clicking the double arrow icon on the right allows you to swap the meanings of outputs 0 and 1.
	Commodity	Select the commodity to be monitored from the list.
	Usage	Select the usage to be monitored from the list.
Input	I/O Type	Select from the list: Standard I/O Not connected
	Name	Enter the name of the wireless device.
	Label	Enter the label of the wireless device (optional).
	I/O Contextualization	Select an option from the list.
	Meaning of output = 0	Engaged (for display only). NOTE: Clicking the double arrow icon on the right allows you to swap the meanings of outputs 0 and 1.
	Meaning of output = 1	Released (for display only). NOTE: Clicking the double arrow icon on the right allows you to swap the meanings of outputs 0 and 1.
	Commodity	Select the commodity to be monitored from the list.
	Usage	Select the usage to be monitored from the list.

Parameters for Contactor with feedback loop and for Impulse Relay

Parameter name		Description
I/O Type		Select from the list: Standard I/O Not connected NOTE: No parameters are displayed if Not connected is selected.
Output/Input Feedback Loop	Name	Enter the name of the wireless device.
	Label	Enter the label of the wireless device (optional).
	Commodity	Select the commodity to be monitored from the list.
	Usage	Select the usage to be monitored from the list.
	I/O Contextualization	Select an option from the list.
	Status name	If you select Custom as contextualization option, then enter the custom name for the device.
	Meaning of output = 0	Displayed values depend on selection of I/O Contextualization. Enter your custom values if you select Custom as contextualization option. NOTE: Clicking the double arrow icon on the right allows you to swap the meanings of outputs 0 and 1.
	Meaning of output = 1	Displayed values depend on selection of I/O Contextualization. Enter your custom values if you select Custom as contextualization option. NOTE: Clicking the double arrow icon on the right allows you to swap the meanings of outputs 0 and 1.