Appendix J.3 ***flex*VUE** Engineer Menu Screens

ACR

The Engineer menu for the ACR includes at least four sub-menus.

Protection Menu
Configuration Menu
Telemetry Menu
Measurement Menu

One or two more sub-menus can be added depending on which optional features are made available.

An Automation menu is added if either Loop Automation or Auto-Changeover are made available.
A Power Quality menu is added if one or more of the following four Power Quality features are made available.
1. Supply Outage Measurement
2. Waveform Capture
3. Harmonic Analysis
4. Sag and Swell Monitoring

When all six menus are available, they are displayed in the following order:

Protection Menu

The Protection menu includes sub-menus as shown below. Sub-menus shown in bold are conditional on feature selection as indicated.

Table 132 ***flex*VUE** Protection Menu

Engineer Menu → Protection
1^st Sub Menu	2^nd Sub Menu	3^rd Sub Menu	4^th Sub Menu	Feature Selection
PROTECTION GLOBAL	GLOBAL CONTROL
	GLOBAL PICKUP⁽¹⁾	PHASE
		EARTH
		SEF
		NPS		Sequence Components
	FAULT RESET
PROT TRIP SETTINGS	AUTO RECLOSE	TRIP 1	PHASE
			PHASE RESET	Reset Curves
			EARTH
			EARTH RESET	Reset Curves
			SEF
			SEF RESET	Reset Curves
			NPS	Sequence Components
			NPS RESET	Reset Curves + Sequence Components
			RECLOSE
		TRIP 2	PHASE
			PHASE RESET	Reset Curves
			EARTH
			EARTH RESET	Reset Curves
			SEF
			SEF RESET	Reset Curves
			NPS	Sequence Components
			NPS RESET	Reset Curves + Sequence Components
			RECLOSE
		TRIP 3	PHASE
			PHASE RESET
			EARTH
			EARTH RESET
			SEF
			SEF RESET
			NPS
			NPS RESET
			RECLOSE
		TRIP 4	PHASE
			PHASE RESET	Reset Curves
			EARTH
			EARTH RESET	Reset Curves
			SEF
			SEF RESET	Reset Curves
			NPS	Sequence Components
			NPS RESET	Reset Curves + Sequence Components
	SINGLE SHOT		PHASE
			PHASE RESET	Reset Curves
			EARTH
			EARTH RESET	Reset Curves
			SEF
			SEF RESET	Reset Curves
			NPS	Sequence Components
			NPS RESET	Reset Curves + Sequence Components
			RESET
	WORK TAG		PHASE
			PHASE RESET	Reset Curves
			EARTH
			EARTH RESET	Reset Curves
			SEF
			SEF RESET	Reset Curves
			NPS	Sequence Components
			NPS RESET	Reset Curves + Sequence Components
	UNDER/OVER FREQ		UNDER FREQ	Under/Over Freq Prot
			OVER FREQ	Under/Over Freq Prot
			NORMAL FREQ CLOSE	Under/Over Freq Prot
	ROCOF			Under/Over Freq Prot
	UNDER/OVER VOLT		UNDER VOLT	Under/Over Voltage Prot
			OVER VOLT	Under/Over Voltage Prot
			UV/OV CONFIG	Under/Over Voltage Prot
	LOSS OF PHASE
	NVD PROTECTION			Neutral Voltage Displacement
	NVD ALARM			Neutral Voltage Displacement
	BROKEN CONDUCTOR PROT			Broken Conductor Avail
	BROKEN CON ALARM			Broken Conductor Avail
PROTECTION CONTROL		COLD LOAD PICKUP
		SYNC CHECK		Sync Check Available
		INRUSH RESTRAINT
		HIGH CURRENT LOCKOUT
		Dead Lockout
		Live Load Blocking
		Sequence
		Fault Period
DIRECTIONAL ELEMENTS		DIRECTIONAL BLOCKING⁽²⁾	PHASE FAULT POLARISE
			EARTH FAULT POLARISE
			SEF POLARISE
			NPS POLARISE
			Vzps COMPENSATION
			HIGH Vzps ALARM
DIRECTIONAL ELEMENTS		DIRECTIONAL PROTECTION	PHASE FAULT POLARISE	Directional Protection ON
			EARTH FAULT POLARISE	Directional Protection ON
			SEF POLARISE	Directional Protection ON
			NPS POLARISE	Directional Protection ON + Sequence Components
FAULT LOCATOR				Fault Locator Available
⁽¹⁾ Only displayed when Per Trip Thresholds are not available. ⁽²⁾ Direction Blocking and Directional Protection are mutually exclusive.

AS

The Engineer menu for the AS includes at least four sub-menus.

Detection Menu
Configuration Menu
Telemetry Menu
Measurement Menu

One or two more sub-menus can be added depending on which optional features are made available.

An Automation menu is added if either Loop Automation or Auto-Changeover are made available.
A Power Quality menu is added if one or more of the following four Power Quality features are made available.
1. Supply Outage Measurement
2. Waveform Capture
3. Harmonic Analysis
4. Sag and Swell Monitoring

When all six menus are available, they are displayed in the following order:

Detection Menu

The Detection menu includes sub-menus as shown below. Sub-menus shown in bold are conditional on feature selection as indicated.

Table 133 ***flex*VUE** Detection Menu

Engineer Menu → Detection
1^st Sub Menu	2^nd Sub Menu	Default Setting	Feature Selection
GLOBAL CONTROL		Active Detection Group A
		Copy Off
		Detection On
		Sectionaliser Off
		E/F On, SEF On	Per Element Detection N/Avail
		Phase Detection On	Per Element Detection Avail
		Phase Mode SECT	Per Element Detection Avail
		Earth Detection On	Per Element Detection Avail
		Earth Mode SECT	Per Element Detection Avail
		SEF Detection On	Per Element Detection Avail
		SEF Mode SECT	Per Element Detection Avail
		SEF Alarm On
		NPS Detection On	Per Element Detection Avail
		NPS Mode SECT
		Single Shot Mode Off
		Supply Fail 3.0 s
SECTIONALISE		Trip on Count 1
		Trip on SEF Count 1
		Trip on NPS Count 1
		Seq Reset Time 30 s
FAULT DETECTION	PHASE	Phase Set 200 Amp
		Phase Pickup x 1.0
	EARTH	Earth Set 40 Amp
		Earth Pickup x 1.0
	SEF	SEF Set 4 Amp
		SEF Pickup x 1.0
	NPS	NPS Set 40 Amp	Sequence Components Avail
		NPS Pickup x 1.0	Sequence Components Avail
FAULT RESET		Fault Reset 50 ms
		Phase Reset 90%
		Earth Reset 90%
		SEF Reset 90%
		NPS Reset 90%	Sequence Components Avail
	SECTIONALISE/TRIP 1/PHASE DETECTION	Definite Time
		Definite Time 1.00 s
		No Instantaneous
DETECTION SETTINGS	SECTIONALISE/TRIP 1/EARTH DETECTION	Definite Time
		Definite Time 1.00 s
		No Instantaneous
	SECTIONALISE/TRIP 1/EARTH DETECTION	Definite Time
		Definite Time 1.00 s
		No Instantaneous
	SECTIONALISE/TRIP 1/SEF DETECTION	Definite Time
		Definite Time 5.00 s
		No Instantaneous
		Alarm Definite Time 1.00 s
	SECTIONALISE/TRIP 1/NPS DETECTION	Definite Time	Sequence Components Avail
		Definite Time 1.00 s	Sequence Components Avail
		No Instantaneous	Sequence Components Avail
	SINGLE SHOT/PHASE DETECTION	Definite Time
		Definite Time 1.00 s
		No Instantaneous
	SINGLE SHOT/EARTH DETECTION	Definite Time
		Definite Time 1.00 s
		No Instantaneous
	SINGLE SHOT/SEF DETECTION	Definite Time
		Definite Time 5.00 s
		No Instantaneous
		Alarm Definite Time 1.00 s
	SINGLE SHOT/NPS DETECTION	Definite Time
		Definite Time 1.00 s
		No Instantaneous
	SINGLE SHOT/RESET	Single Shot Reset Time 0 s
	UNDER OVER VOLTAGE/UNDER VOLTAGE	UV Detection Off
		UV Mode ALARM
		Phase Logic AND
		Pickup Voltage 0.90 pu
		Definite Time 1.00 s
	UNDER OVER VOLTAGE/OVER VOLTAGE	OV Detection Off
		OV Mode ALARM
		Phase Logic AND
		Pickup Voltage 1.10 pu
		Definite Time 1.00 s
	UNDER OVER VOLTAGE/UV/OV CONFIGURATION	Nom P-E V 6.300 kV
		Definite Time
		Fault Reset 50ms
	BROKEN CONDUCTOR DETECTION	Broken Conductor Detection Off
		Set 1.00 INPS/IPPS	Broken Conductor Available
		Definite Time 10.00 s	Broken Conductor Available
		Reset 90%	Broken Conductor Available
		Reset Time 0.05 s	Broken Conductor Available
COLD LOAD PICKUP		CLP Phase Off
		CLP Earth Off
		CLP SEF Off
		CLP NPS Off	Sequence Components Avail
		Cold Load Time 120 min
		Cold Load Mult x 2.0
SYNC CHECK		Sync Check Off	Sync Check Available
		Sync Check Inactive	Sync Check Available
		Close Retry Off	Sync Check Available
		Close Retry 300s	Sync Check Available
		Voltage On	Sync Check Available
		Voltage Diff 0.02 pu	Sync Check Available
		Voltage Min 0.50 pu	Sync Check Available
		Voltage Max 200 pu	Sync Check Available
		Nom P-E V 6.30 kV	Sync Check Available
		Frequency On	Sync Check Available
		Frequency Diff 0.10 Hz	Sync Check Available
		Frequency Min 45.00 Hz	Sync Check Available
		Frequency Max 65.00 Hz	Sync Check Available
		Phase On	Sync Check Available
		Phase Diff 6 deg	Sync Check Available
INRUSH RESTRAINT		Inrush Off
		Inrush Time 0.10 s
		Inrush Mult x 4.0
		Inrush Type Zero Detect
		Inrush Type SOHIR	SOHIR Available
		SOHIR Logic AND	SOHIR Available
		SOHIR Thres 20%	SOHIR Available
Live Load Block		Off
FAULT LOCATOR		Fault Locator Off	Fault Locator Available
		R_PPS 0.0001 ohm/km	Fault Locator Available
		X_PPS 0.0001 ohm/km	Fault Locator Available
		R_zPS 0.0001 ohm/km	Fault Locator Available
		X_zPS 0.0001 ohm/km	Fault Locator Available
Fault Period		10 s	Close on Fault Trip Available Per Element Detection Available
DIRECTIONAL ELEMENTS	DIRECTIONAL BLOCK/PHASE FAULT POLARISE	Fault Direction Forward & Reverse	Directional Blocking On
		Low Polarising Block Off	Directional Blocking On
		Minimum V_QUAD 500 V	Directional Blocking On
		Characteristic Angle -45 deg	Directional Blocking On
		Voltage Memory Off	Directional Blocking On
	DIRECTIONAL BLOCK/EARTH FAULT POLARISE	Decision V_ZPS	Directional Blocking On
		Fault Direction Forward and Reverse	Directional Blocking On
		Low Polarising Block Off	Directional Blocking On
		Minimum V_ZPS 500 V	Directional Blocking On
		Characteristic Angle 135 deg	Directional Blocking On
	DIRECTIONAL BLOCK/SEF FAULT POLARISE	Decision V_ZPS	Directional Blocking On
		Fault Direction Forward and Reverse	Directional Blocking On
		Low Polarising Block Off	Directional Blocking On
		Minimum V_ZPS 500 V	Directional Blocking On
		Characteristic Angle 135 deg	Directional Blocking On
	DIRECTIONAL BLOCK/NPS FAULT POLARISE	Fault Direction Forward & Reverse	Directional Blocking On + Sequence Components Available
		Low Polarising Block Off	Directional Blocking On + Sequence Components Available
		Minimum V_NPS 500V	Directional Blocking On + Sequence Components Available
			Directional Blocking On + Sequence Components Available
	V_ZPS COMPENSATION	V_ZPS Balancing Off	Directional Blocking On
	HIGH V_ZPS ALARM	High Alarm Mode Off	Directional Blocking On
		High Time 10 s	Directional Blocking On
		High Set-point 500 V	Directional Blocking On
	DIRECTIONAL DETECTION/PHASE FAULT POLARISE	Low Polarising Voltage Action – No Action	Directional Detection On
		Minimum V_QUAD 500 V	Directional Detection On
		Characteristic Angle -45 deg	Directional Detection On
		Forward Sector 90 deg	Directional Detection On
		Reverse Sector 90 deg	Directional Detection On
		Voltage Memory Off	Directional Detection On
	DIRECTIONAL DETECTION/EARTH FAULT POLARISE	Decision V_ZPS	Directional Detection On
		Low Polarising Voltage Action – No Action	Directional Detection On
		Minimum V_ZPS 500 V	Directional Detection On
		Characteristic Angle 135 deg	Directional Detection On
		Forward Sector 90 deg	Directional Detection On
		Reverse Sector 90 deg
	DIRECTIONAL DETECTION/SEF FAULT POLARISE	Decision V_ZPS	Directional Detection On
		Low Polarising Voltage Action – No Action	Directional Detection On
		Minimum V_ZPS 500 V	Directional Detection On
		Characteristic Angle 135 deg	Directional Detection On
		Forward Sector 90 deg	Directional Detection On
		Reverse Sector 90 deg	Directional Detection On
	DIRECTIONAL DETECTION/NPS FAULT POLARISE	Low Polarising Voltage Action – No Action	Directional Detection On + Sequence Components Available
		Minimum V_NPS 500 V	Directional Detection On + Sequence Components Available
		Characteristic Angle 120 deg	Directional Detection On + Sequence Components Available
		Forward Sector 90 deg	Directional Detection On + Sequence Components Available
		Reverse Sector 90 deg	Directional Detection On + Sequence Components Available
	V_ZPS COMPENSATION	VZPS Balancing Off	Directional Detection On
	HIGH V_ZPS ALARM	High Alarm Mode Off	Directional Detection On
		High Time 10 s	Directional Detection On
		High Set-point 500 V	Directional Detection On

NOTE: Directional Blocking and Directional Detection are mutually exclusive features.

Configuration Menu (ACR and AS)

The Configuration menu consists of at least 5 sub-menus some of which have another level of sub-menus. When IOEX is made available, a sixth first level sub-menu is created which has its own sub-menus for IOEX-A and IOEX-B.

Table 134 ***flex*VUE** Configuration Menu

Engineer Menu → Configuration Menu
1^st Sub Menu	2^nd Sub Menu	Feature Selection
SYSTEM SETTINGS	DISPLAY
	NETWORK PARAMETERS
	METERING PARAMETERS
FEATURE SELECTION	PROTECTION/DETECTION⁽¹⁾
	AUTOMATION
	GENERAL
	COMMUNICATIONS
	POWER QUALITY
	FAULT LOCATOR
RADIO SETTINGS
MAINTENANCE	BATTERY TEST
IOEX STATUS	IOEX Module A	IOEX Available
	IOEX Module B	IOEX Available
USER DEFINED CONTROL
⁽¹⁾ An ACR has a Protection sub-menu in Feature Selection, an AS has a Detection sub-menu.

Power Quality Menu (ACR and AS)

The Power Quality is not displayed unless at least one of the three power quality features supported by the operator interface has been made available. These features are:

Supply Outages
Sag and Swell
Waveform Capture

A fourth feature, Harmonic Analysis can only be configured and monitored using WSOS. If Harmonic Analysis is the only power quality feature that’s available, the Power Quality menu will not be displayed on the operator interface.

Table 135 ***flex*VUE** Power Quality Menu

Engineer Menu → Power Quality Menu
1^st Sub Menu	2^nd Sub Menu	Feature Selection
SUPPLY OUTAGES		Supply Outage Available
SAG SWELL MENU⁽¹⁾	SAG/SWELL MONITORING	Sag/Swell Available
	SAG MONITORING	Sag/Swell Available
	SWELL MONITORING	Sag/Swell Available
WAVE CAPTURE MENU	WAVEFORM CAPTURE	Waveform Capture Available
	WAVEFORM TRIGGER	Waveform Capture Available
⁽¹⁾ Not supported when the controller is configured as an AS.

Telemetry Menu (ACR and AS)

The Telemetry Menu has two sub-menus:

Configure Ports Menu
Configure Communications

Configure Ports

The Configure Ports sub-menus are slightly different for PowerLogic ADVC Controller due to the different communications ports available on this controller.

Table 136 PowerLogic ADVC ***flex*VUE** Telemetry Menu

1st Sub Menu	2nd Sub Menu
CONFIGURE PORTS MENU	IOEX/WSOS
	Modem
	10BASE-T
	10BASE-T 2
	USB 1
	USB 2
	USB 3

Configure Communications (ACR and AS)

The Configure Communications menu has three sub-menus by default but more are created when additional features are made available through Feature Selection.

Table 137 ***flex*VUE** Configure Communications Menu

Engineer Menu → Telemetry Menu → Configure Communications
1^st Sub Menu	2^nd Sub Menu	Feature Selection
WSOS MENU	WSOS COMMS
	WSOS COMMS STATS
DNP3 MENU	DNP COMMS
	DNP COMMS STATS
	DNP TRANS SERVICES
	DNP UNSOLICITED
	DNP DIAGNOSTICS
	DNP DATABASE CONFIG
TRACE MENU	COMMS TRACE
	COMMS TRACE STATS
IOEX MENU	IOEX Module A	IOEX Available
	IOEX Module B	IOEX Available
IEC 60870-5-101/4	IEC-101 COMMS	IEC 60870-5-101/4 Available
	IEC-101 COMMS STATS	IEC 60870-5-101/4 Available
	IEC-101 TRANS SRVCS	IEC 60870-5-101/4 Available
	IEC-101 CONFIG	IEC 60870-5-101/4 Available
MODBUS MENU	MBUS COMMS	Modbus Available
	MBUS COMMS STATS	Modbus Available
NTP MENU	NTP OFF	NTP + Time Zone Available
	NTP SERVER 1	NTP + Time Zone Available
	NTP SERVER 2	NTP + Time Zone Available
	NTP SERVER 3	NTP + Time Zone Available

Automation Menu (ACR and AS)

The Automation menu is similar to the Power Quality menu in that it is not displayed unless at least one applicable feature is available. In the case of automation, applicable features are:

Loop Automation
Auto-Changeover

These two features are mutually exclusive so the Automation menu will be displayed if either of them is available.

Table 138 flexVUE Automation Menu

Engineer Menu → Automation Menu
1^st Sub Menu	2^nd Sub Menu	Feature Selection
LOOP AUTOMATION MENU	LA CONFIGURATION	Loop Automation Available
	LA COMMUNICATIONS	Loop Automation Available + LA Logic Intelligent
	OVERLOAD CONTROL	Loop Automation Available + LA Logic Intelligent + Tie Control Message
AUTO-CHANGEOVER MENU	ACO CONFIG	Auto-Changeover Available
	ACO COMMS	Auto-Changeover Available
	ACO COMMS STATS	Auto-Changeover Available
	ACO TIMERS	Auto-Changeover Available

Measurement Menu (ACR and AS)

The Measurement menu has 6 first level sub menus. Sequence Components available adds a Sequence sub-menu to Voltage.

Table 139 ***flex*VUE** Measurement Menu

Engineer Menu → Automation Menu
1^st Level Sub Menu	2^nd Level Sub Menu	3^rd Level Sub Menu	Feature Selection
CURRENT	MAGNITUDE AND ANGLE	A PHASE
		B PHASE
		C PHASE
		EARTH
	SEQUENCE	I_PPS	Sequence Components
VOLTAGE	PHASE/LINE SRC-LD	I_NPS	Sequence Components
		A-E (A-B) Volts⁽¹⁾
		B-E (B-C) Volts
		C-E (C-A) Volts
		A-E (A-B) Angles
		B-E (B-C) Angles
		C-E (C-A) Angles
	SEQUENCE	V_pps	Sequence Components
		V_nps	Sequence Components
		V_zps	Sequence Components
FREQUENCY	Frequency
	Source Frequency
	Load Frequency
POWER	THREE PHASE
	A PHASE
	B PHASE
	C PHASE
ENERGY	Total
	Forward
	Reverse
SYNCHRONIZATION	Global In Sync		Sync Check Available
	Voltage In Sync		Sync Check Available
	Frequency In Sync		Sync Check Available
	Phase In Sync		Sync Check Available
DEMAND	DAILY MAX DEMAND
	WEEKLY MAX DEMAND
	MONTHLY MAX DEMAND
⁽¹⁾ Voltages can be displayed as Phase to Earth or Phase to Phase values.

Appendix J.3 ­ flexVUE Engineer Menu Screens

ACR